Bently Nevada 330104-00-10-10-02-05 Proximity Probe – 3300 XL Series

Bently Nevada 330104-00-10-10-02-05 — 8 mm Eddy-Current Proximity Probe in the 3300 XL Transducer System

The Bently Nevada 330104-00-10-10-02-05 is an 8 mm eddy-current proximity probe belonging to the 3300 XL 8 mm Proximity Transducer System. Within a machinery protection architecture, this probe functions as the primary sensing element responsible for converting mechanical displacement into a proportional DC voltage signal. It operates on the principle of electromagnetic induction: a high-frequency oscillator in the paired driver/oscillator-demodulator energizes a coil wound at the probe tip, generating a focused magnetic field. When a conductive target surface — typically a shaft journal — enters this field, eddy currents are induced on the target surface, loading the oscillator circuit and producing a measurable impedance change. The driver converts this impedance variation into a linear DC output spanning −1 VDC to −17 VDC across a calibrated gap range of 0.25 mm to 2.54 mm (10 mil to 100 mil), with a nominal sensitivity of 7.87 V/mm (200 mV/mil).

This probe is designed for continuous, non-contact measurement in rotating machinery environments where shaft radial vibration, axial position, differential expansion, and eccentricity must be monitored with sub-micron resolution. Its 1.0 m integral cable minimizes connector count in the signal path, directly reducing susceptibility to intermittent contact faults in high-vibration installations. The probe mates with a 1.0 m 3300 XL extension cable to achieve the standard 2.0 m total system cable length required by the matched driver calibration.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330104-00-10-10-02-05 probe tip houses a precision-wound coil embedded in a thermoplastic housing rated to 177 °C continuous. The coil geometry is fixed at manufacture and laser-trimmed to match the 3300 XL driver calibration curve, ensuring interchangeability within the matched system without field recalibration — provided the target material matches the standard AISI 4140 specification. Deviation from this target alloy (e.g., 316 stainless steel or titanium) introduces a non-linearity error that must be corrected via a material-specific calibration factor applied at the driver or monitoring rack level.

The integral cable construction eliminates the probe-to-extension connector junction at the probe body, which is the highest-stress point in a conventional two-piece probe assembly. In turbomachinery bearing housings where vibration amplitudes at the probe mounting bracket can exceed 10 g, this design choice measurably reduces the probability of intermittent signal dropout caused by connector fretting corrosion. The cable jacket is rated for continuous immersion in lubricating oil and short-term exposure to steam condensate, consistent with the thermal and chemical environment of a steam turbine bearing pedestal.

EMC performance is governed by the shielded coaxial cable construction and the driver’s differential input architecture. The shield is grounded at the driver end only (single-point grounding), preventing ground loop currents from modulating the signal. This topology maintains signal integrity in environments with high common-mode noise, such as variable-frequency drive (VFD) motor rooms or generator halls where conducted and radiated emissions from power electronics can exceed 10 V/m at frequencies up to 1 GHz. The driver’s oscillator frequency (nominally 1.0 MHz for the 8 mm probe) is selected to be well above the frequency range of industrial power harmonics (up to ~2 kHz) and well below the self-resonance of the cable assembly, preserving measurement bandwidth to the specified 10 kHz upper limit.

The probe body threads are machined to a tolerance class that ensures repeatable installation depth when used with standard 3300 XL probe holders. Axial positioning accuracy at installation directly determines the static gap voltage, which must fall within the linear range (nominally −10 VDC ± 1 VDC at the 1.27 mm center gap) for the monitoring system to operate within its specified accuracy band. A gap voltage outside this window does not damage the probe but will cause the driver to output a clipped or saturated signal, triggering a false alert or masking a real vibration event.

System Integration Benefits

• Direct rack compatibility: The 330104-00-10-10-02-05 is factory-calibrated to interface with Bently Nevada 3500 Series monitors (3500/40M, 3500/42M, 3500/45, 3500/46M) without additional signal conditioning, preserving the rack’s ±1% full-scale accuracy specification.
• Deterministic signal latency: The analog DC output of the eddy-current system introduces zero processing latency between shaft displacement and monitor input — critical for machinery protection systems where trip response time must be ≤1 ms from threshold crossing to relay actuation.
• Non-contact operation eliminates wear: With no mechanical contact between probe and shaft, the sensor introduces zero friction load and has no wear-limited service life under normal operating conditions, supporting continuous 24/7 monitoring across multi-year maintenance intervals.
• High-resolution displacement data: At 7.87 V/mm sensitivity and a driver output resolution of approximately 0.001 mm, the system resolves shaft displacement changes well below the 25 µm (1 mil) alarm threshold typical of API 670-compliant installations.
• Wide thermal operating envelope: The −40 °C to +177 °C probe tip rating covers both arctic cold-start conditions and the bearing housing temperatures of high-pressure steam turbines, eliminating the need for thermal derating calculations in most industrial applications.
• Intrinsically safe configurations available: FM and CSA approvals for intrinsically safe (IS) installations allow deployment in Zone 0/1 hazardous areas (IEC 60079) without additional IS barriers in the signal loop, simplifying the safety instrumented system (SIS) architecture.
• Diagnostic transparency via gap voltage monitoring: The static DC gap voltage provides a continuous, real-time indicator of probe installation integrity. A drift in gap voltage at constant shaft position indicates probe loosening, target surface wear, or cable damage — enabling predictive maintenance before a measurement fault occurs.
• Drop-in replacement for existing 3300 XL installations: The standardized probe body dimensions, connector type, and calibration curve allow direct substitution in existing installations without re-gapping, re-cabling, or reconfiguring the monitoring rack, minimizing planned outage duration during spare-part replacement.

Quality Assurance & Global Logistics

Every unit of the Bently Nevada 330104-00-10-10-02-05 supplied by siemensplc.com is sourced through verified industrial distribution channels and subjected to a structured pre-shipment inspection protocol. Authenticity verification cross-references the part number, date code, and manufacturer markings against Bently Nevada / Baker Hughes published documentation. Physical inspection covers probe tip condition, cable jacket integrity, connector pin geometry, and housing markings. Units that do not pass inspection are quarantined and not shipped.

Shipments originate from our warehouse in Xiamen, China — a major export hub with direct access to international freight carriers including DHL Express, FedEx International Priority, and UPS Worldwide Expedited. In-stock orders are typically dispatched within 1–3 business days. Export documentation — commercial invoice, packing list, and certificate of origin — is prepared as standard for all international shipments. HS code classification and ECCN determination are available on request for regulated procurement processes. Bulk orders of 5+ units qualify for consolidated freight options and volume pricing; contact us for a formal quotation.

All units are covered by a 12-month warranty against defects in materials and workmanship from the date of shipment. Warranty claims are handled directly by our technical team with a target response time of one business day.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.