Bently Nevada 330104-00-14-10-01-CN Proximity Transducer

330104-00-14-10-01-CN In Stock Now — Every Hour of Downtime Costs You More Than This Module

Your compressor train is down. The control room is on the phone. Maintenance is standing by. The bottleneck is a single proximity transducer — and you need it today, not in six weeks. The Bently Nevada 330104-00-14-10-01-CN is a complete 8mm eddy current proximity transducer system from the 3300 XL Series, and we have it on the shelf in Xiamen, ready to clear customs and board the next DHL flight to your site.

This is not a catalog listing. This is a live inventory position. We stock this part because we know what it means when a turbine-generator train trips on a high vibration alarm and the spare parts room comes up empty.

URGENT REQUIREMENT? Contact: [email protected] | WhatsApp: +86 18359268345

Quick Technical Datasheet

Troubleshooting & Replacement Tips

Ten years of field work teaches you that most 330104-series failures fall into four categories. Know them before you pull the probe.

1. Proximitor® Output Drift / Flat-Line Reading
If your 3500 rack is showing a static DC voltage that doesn’t respond to shaft movement, the Proximitor® oscillator circuit has likely failed — not the probe. Before condemning the full system, disconnect the extension cable at the Proximitor® and measure the oscillator frequency with a frequency counter at the coax center pin. Nominal is 1.0 MHz ±10%. No signal = Proximitor® failure. Correct signal = suspect the extension cable or probe tip damage.

2. High Vibration Alarm with No Process Change
Check the probe gap first. The 330104 8mm probe has a nominal installation gap of 50 mil (1.27 mm) from the shaft surface, corresponding to a Proximitor® output of approximately –10 VDC. If the gap has shifted due to bearing wear or thermal growth, recalibrate the gap before replacing the transducer. A misdiagnosed gap issue has killed more spare parts budgets than actual sensor failures.

3. Extension Cable Continuity Failure
The 10-meter extension cable in this system is impedance-matched to the probe. Do not substitute with generic coaxial cable — the characteristic impedance mismatch will corrupt the oscillator signal and produce erratic output. When replacing, always use the factory-matched cable supplied with this system. Measure center-conductor resistance (should be <2 Ω) and shield continuity before installation.

4. System Swap — Configuration Checklist
When installing a replacement 330104-00-14-10-01-CN into an existing 3500 or 3300 rack:

• Verify the rack channel is configured for 8mm probe sensitivity (200 mV/mil). Do not mix with 5mm probe channels (100 mV/mil) — the rack will not alarm correctly.
• Confirm the Proximitor® supply voltage at the rack terminal: must be –24 VDC ±1 VDC. Low supply voltage causes output compression and false low-vibration readings.
• After installation, perform a static gap check: adjust probe position until Proximitor® output reads –10 VDC ±0.5 VDC at the nominal shaft gap.
• Run a slow-roll check at <600 RPM to verify runout compensation is within API 670 limits before returning the machine to service.
• The CN suffix designates a specific connector termination. Confirm your extension cable termination matches before ordering — do not assume interchangeability with -00 or -05 suffix variants.

Reliability in Harsh Conditions

The 3300 XL platform was not designed for a clean instrument room. It was designed for the bearing housing of a 50 MW steam turbine running at 3,000 RPM in a coastal refinery where ambient temperature swings 60°C between seasons and the air smells like hydrogen sulfide.

The probe body of the 330104-00-14-10-01-CN is constructed from 316 stainless steel with a PEEK (polyether ether ketone) tip — chemically inert to most process hydrocarbons, resistant to chloride stress corrosion, and mechanically stable up to 121°C continuous. The integral cable uses a fluoropolymer jacket rated for the same temperature range, with a stainless armor braid that survives the vibration environment of the probe mounting boss without fatigue cracking.

The Proximitor® enclosure is rated IP67 — fully sealed against water ingress during washdown operations. Internal potting compound protects the oscillator circuit from humidity-induced PCB corrosion, a common failure mode in tropical and coastal installations. We have seen units pulled from offshore platform junction boxes after five years of service that still calibrate within factory specification.

Vibration immunity is not an afterthought. The probe and Proximitor® are tested to IEC 60068-2-6 sinusoidal vibration profiles — 10 to 2,000 Hz sweep — without output deviation. In practice, this means the sensor does not generate false vibration signals from its own mounting structure, which is a real problem with lower-grade proximity systems installed on high-frequency machinery.

Global Express Logistics

Our warehouse is located in Xiamen, Fujian Province — one of China’s primary export hubs with direct DHL and FedEx gateway access. This is not a drop-ship arrangement. The physical unit is on our shelf, inspected, and ready to pack.

Standard export process for urgent orders:

• Order confirmed before 14:00 CST → Same-day dispatch via DHL Express or FedEx International Priority
• Commercial invoice, packing list, and Certificate of Origin prepared within 2 hours of order confirmation
• HS Code: 9031.80 (instruments for measuring or checking) — pre-cleared for most destinations without import license requirements
• Typical transit times: Southeast Asia 1–2 days | Middle East 2–3 days | Europe 3–4 days | Americas 3–5 days
• Tracking provided immediately upon dispatch — AWB number sent to your email and WhatsApp
• Emergency freight options: For AOG or plant-down situations, we can arrange next-flight-out courier with airport-to-airport transit. Contact us directly to activate this service.

All shipments include full export documentation. For customers in sanctioned or restricted jurisdictions, we conduct compliance screening prior to order acceptance. We do not ship to embargoed destinations.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
© 2026 siemensplc.com. All rights reserved.