Bently Nevada 330104-00-14-50-02-00 Proximity Probe – 3300 XL

Bently Nevada 330104-00-14-50-02-00 — Eddy-Current Proximity Probe for Rotating Machinery Protection

The Bently Nevada 330104-00-14-50-02-00 is an 8 mm eddy-current proximity probe belonging to the 3300 XL Series — a platform that has accumulated decades of field deployment across turbomachinery protection systems in oil & gas, power generation, and petrochemical processing. This specific part number encodes a 14-inch (355 mm) integral armored cable, standard coaxial termination (-02), and a non-intrinsically-safe configuration (-00), making it the default selection for general-purpose machinery monitoring in non-classified areas.

Unlike contact-type displacement transducers, the eddy-current operating principle imposes zero mechanical load on the rotating shaft. The probe tip generates a high-frequency electromagnetic field (typically 1 MHz carrier); when a conductive target enters the sensing zone, eddy currents are induced on the target surface, loading the oscillator circuit and producing a DC-proportional output voltage. This mechanism delivers a flat frequency response from DC to 10 kHz, which is essential for capturing both slow-roll runout at startup and high-frequency subsynchronous instabilities during full-load operation.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 3300 XL probe architecture separates the oscillator/demodulator electronics from the probe body itself, placing them inside the Proximitor® sensor module (330180 series). This division of function has a direct consequence for field reliability: the probe body contains no active components, no PCB, and no solder joints exposed to process heat. The only failure modes at the probe level are mechanical — cable abrasion, tip contamination, or thread damage — all of which are visually detectable during routine inspection.

EMC Design: The integral armored cable (stainless steel braid, -50- segment in the part number) provides continuous 360° shielding from probe tip to connector. This construction attenuates radiated interference from variable-frequency drives, high-current bus bars, and adjacent motor windings. In practice, the shielded coaxial path maintains signal integrity at carrier frequencies around 1 MHz even when routed through cable trays carrying 480 VAC power conductors — a common constraint in compressor train installations.

Thermal Stability: The probe body is constructed from 316 stainless steel with a ceramic-filled epoxy tip compound. This material combination maintains dimensional stability across the full –35 °C to +177 °C operating envelope. Thermal expansion of the probe body is predictable and linear, meaning the gap voltage baseline does not drift significantly with temperature cycling — a property that reduces false alarms during turbine startup transients when metal temperatures change rapidly.

Scale Factor Traceability: Each 330104-series probe is factory-calibrated as a matched set with a specific Proximitor® sensor against an AISI 4140 steel target. The 7.87 V/mm (200 mV/mil) scale factor is verified at the factory and documented on the calibration data sheet shipped with the unit. This traceability eliminates the need for field calibration on like-for-like replacement, reducing maintenance window duration by the time that would otherwise be spent on gap-setting verification and output scaling.

Redundancy Compatibility: The 3300 XL system supports dual-probe redundant configurations on a single monitor channel. The 330104-00-14-50-02-00 can be installed as either the primary or redundant element in a two-out-of-two (2oo2) or one-out-of-two (1oo2) voting architecture, depending on the safety integrity level (SIL) requirement of the machinery protection loop. The monitor’s internal arbitration logic selects the active channel based on signal validity flags, with no operator intervention required during switchover.

System Integration Benefits

• Zero-recalibration replacement: The factory-matched 200 mV/mil scale factor is consistent across all 330104-series probes. Swapping a failed probe with a stocked spare does not require re-entering scale factor constants in the monitor rack, eliminating a common source of commissioning error during emergency maintenance.
• Deterministic DC-coupled output: The DC-to-10 kHz flat response captures both static position (gap voltage) and dynamic vibration on a single signal path. This eliminates the need for separate position and vibration transducers on the same measurement plane, reducing wiring count and potential failure points per measurement channel.
• API 670 compliance by design: The probe, extension cable, and Proximitor® sensor are qualified as a matched system under API 670 §5. This pre-qualification satisfies EPC contractor and insurance underwriter requirements without additional third-party testing, shortening project commissioning schedules.
• Diagnostic transparency via gap voltage: The Proximitor® output at nominal gap (–10.0 VDC ± 0.5 V at 1.0 mm) serves as a continuous self-diagnostic signal. Deviations outside this window — caused by probe tip fouling, cable damage, or target runout — are immediately visible on the monitor’s OK relay output, enabling condition-based maintenance rather than time-based probe replacement.
• Broad target material database: While calibrated for AISI 4140, Bently Nevada publishes correction factors for over 30 target materials including 17-4 PH stainless, Inconel 718, and titanium alloys. This allows the same probe model to be deployed across mixed-material shaft inventories without stocking material-specific variants.
• IP67 environmental sealing: The probe body and cable junction are sealed to IP67, permitting direct exposure to oil mist, cooling water spray, and process condensate without degradation of the coaxial signal path. This rating is verified at the factory and does not require field-applied sealant.
• Backward compatibility with 3300 monitor racks: The 3300 XL probe series operates with both the legacy 3300/16 monitor and the current 3500 series rack when paired with the appropriate Proximitor® sensor. This compatibility protects capital investment in existing monitor infrastructure during phased plant upgrades.
• Reduced spare parts inventory complexity: The standardized 8 mm form factor and 200 mV/mil output mean a single probe model covers radial vibration, axial position, and differential expansion measurement planes across multiple machine trains. Procurement teams can consolidate spare holdings around one part number rather than maintaining separate inventories for each measurement function.

Quality Assurance & Global Logistics

siemensplc.com sources the Bently Nevada 330104-00-14-50-02-00 through verified supply channels with full documentation traceability. Every unit dispatched from our Xiamen warehouse undergoes a structured pre-shipment inspection protocol: visual examination of probe tip geometry and thread condition, coaxial connector integrity check, cable continuity and insulation resistance measurement (≥100 MΩ at 500 VDC), and label authentication against Bently Nevada serialization records.

Packaging follows OEM specifications — individual anti-static foam inserts, desiccant sachets, and rigid outer cartons rated for air freight handling. Each shipment includes a commercial invoice, packing list, and certificate of conformance. Export documentation for customs clearance (HS Code 9031.80) is prepared in compliance with Xiamen Customs regulations, supporting smooth import processing in the EU, US, Southeast Asia, and Middle East markets.

Logistics options from Xiamen Gaoqi International Airport and Xiamen Port include DHL Express (2–4 business days to most destinations), FedEx International Priority (3–5 business days), and sea freight consolidation for bulk orders. Expedited same-day dispatch is available for orders confirmed before 14:00 CST.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.