Bently Nevada 330104-00-23-05-01-00 Proximity Transducer – 3300 XL Series

Bently Nevada 330104-00-23-05-01-00: 8 mm Eddy-Current Proximity Transducer in Rotating Machinery Protection Systems

The Bently Nevada 330104-00-23-05-01-00 is an 8 mm eddy-current proximity transducer assembly belonging to the 3300 XL NSv platform. Within a machinery protection architecture, this transducer occupies the first stage of the signal chain: it converts mechanical displacement — shaft radial vibration, axial position, or eccentricity — into a proportional DC-biased voltage that downstream monitors interpret in real time. Unlike accelerometers, which integrate twice to derive displacement and accumulate phase error at low frequencies, an eddy-current probe delivers a direct, DC-coupled displacement signal from 0 Hz to 10,000 Hz, making it the preferred sensor for API 670-compliant turbomachinery protection on steam turbines, gas turbines, centrifugal compressors, and high-speed pumps.

The 330104-00-23-05-01-00 integrates the NSv (Non-contacting vibration) Proximitor driver electronics within the probe body itself, eliminating the separate Proximitor enclosure required by earlier 3300 XL generations. This integration reduces field wiring complexity, removes one potential failure node from the signal path, and allows the probe-to-monitor cable run to carry a conditioned ±17 VDC output rather than a raw RF oscillator signal susceptible to cable-capacitance detuning.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

Oscillator-Demodulator Architecture. The NSv Proximitor driver embedded in the 330104-00-23-05-01-00 operates on a fixed-frequency RF oscillator (nominally 1.0 MHz). The oscillator drives the probe coil, which generates an alternating magnetic field at the probe tip. When a conductive target enters the field, eddy currents are induced on the target surface, loading the oscillator circuit and reducing its amplitude. The demodulator stage rectifies and filters this amplitude-modulated signal, producing the linear DC output voltage proportional to gap distance. The entire oscillator-demodulator chain is temperature-compensated to maintain scale-factor accuracy within ±1% across the full −35 °C to +85 °C driver operating range.

EMC Design and Shielding. The probe cable uses a triaxial construction: the inner conductor carries the RF drive signal, the inner shield is driven at the same potential as the center conductor (guard drive) to eliminate cable-capacitance loading on the oscillator, and the outer shield provides EMI rejection. This guard-drive topology is critical in high-voltage switchgear environments and variable-frequency drive (VFD) installations where common-mode noise on a standard coaxial cable would detune the oscillator and introduce measurement error. The outer shield is grounded at the Proximitor/driver end only, preventing ground-loop currents from corrupting the signal.

Intrinsic Safety Barrier Compatibility. The ATEX Zone 1 (Ex ia IIC T6) certification means the 330104-00-23-05-01-00 is designed to operate behind a certified Zener barrier or galvanic isolator that limits energy into the hazardous area to below the ignition threshold of Group IIC gases (hydrogen, acetylene). The probe’s inductance and capacitance parameters are documented in the Bently Nevada Entity Parameters sheet, allowing engineers to verify barrier compatibility without physical testing. This is a mandatory step for installations in hydrogen-cooled generators or LNG compressor trains.

Material-Specific Calibration Sensitivity. The standard 7.87 V/mm scale factor is calibrated against AISI 4140 steel. For shafts manufactured from austenitic stainless steel (e.g., 316L), titanium alloys, or nickel superalloys (Inconel 718), the eddy-current penetration depth and resistivity differ, shifting the effective scale factor by up to ±8%. Bently Nevada provides material-specific calibration curves; when ordering for non-standard shaft materials, specify the target material so the correct calibration data is supplied with the unit.

System Integration Benefits

• Direct DC-coupled displacement output eliminates the double-integration error inherent in accelerometer-based displacement measurement, providing phase-accurate vibration data from 0 Hz through 10 kHz without signal conditioning artifacts.
• Integrated NSv driver removes the separate Proximitor enclosure from the field installation, reducing junction box count, cable terminations, and associated maintenance touchpoints in the signal chain.
• API 670 fifth-edition compliance satisfies the machinery protection standard for radial vibration, axial position, and eccentricity measurement on critical turbomachinery, supporting insurance and regulatory audit requirements without additional sensor qualification.
• Plug-compatible with 3500 and 3300 monitor platforms — the M10 × 1.0 mounting thread, BNC-compatible connector, and −24 VDC supply requirement are identical across the 3300 XL family, allowing probe replacement without monitor reconfiguration or re-ranging.
• ATEX Zone 1 / FM intrinsically safe certification permits installation in classified hazardous areas (refineries, offshore platforms, LNG terminals) without additional explosion-proof enclosures around the probe body, reducing installation hardware cost.
• Guard-drive triaxial cable maintains oscillator stability in high-EMI environments including VFD motor rooms and high-voltage switchgear bays, where standard coaxial probes exhibit measurable scale-factor drift under common-mode interference.
• Deterministic frequency response to 10,000 Hz captures sub-synchronous instabilities (oil whirl at 0.43–0.48×), synchronous imbalance (1×), and higher-order blade-pass frequencies in a single sensor channel, reducing the sensor count required for full spectral coverage.
• Compatibility with System 1 Evolution software enables continuous online trending, alarm setpoint management, and automated diagnostic rule execution against the probe’s raw gap voltage and dynamic vibration signal simultaneously, supporting condition-based maintenance programs without additional hardware.
• 316 stainless steel probe body resists corrosion in wet-gas, sour-service (H₂S), and high-humidity environments, maintaining dimensional stability of the M10 × 1.0 mounting thread over extended service intervals.
• Factory-documented entity parameters (inductance, capacitance, Vmax, Imax) allow direct barrier selection from certified barrier catalogs, compressing the ATEX installation engineering timeline from weeks to hours.

Quality Assurance & Global Logistics

Every 330104-00-23-05-01-00 unit supplied through siemensplc.com is sourced from verified supply channels and undergoes a structured incoming inspection protocol before dispatch. Inspection steps include continuity and insulation resistance verification on the probe cable, scale-factor spot-check at the nominal −10 VDC gap voltage using a calibrated test fixture, and visual inspection of the M10 thread and connector body for mechanical damage. Units that do not meet the Bently Nevada factory specification are quarantined and not shipped.

Original manufacturer packaging, factory calibration documentation, and lot traceability records are retained for each unit. For critical installations requiring full material traceability — such as nuclear auxiliary systems or offshore safety-instrumented systems — date codes and lot numbers are provided in the shipping documentation upon request.

Logistics are managed from our warehouse in Xiamen, China. Standard export packaging uses anti-static foam inserts and moisture-barrier bags to protect the probe coil and cable assembly during transit. Shipments are dispatched via DHL Express, FedEx International Priority, or UPS Worldwide Expedited depending on destination and urgency. Typical transit times are 3–5 business days to Europe and North America, 2–3 business days to Southeast Asia, and 1–2 business days to Hong Kong, Taiwan, and South Korea. Air freight on palletized bulk orders is available for quantities exceeding 20 units. All shipments include commercial invoice, packing list, and certificate of origin for customs clearance. Export classification is EAR99 for most destinations; customers in controlled-technology jurisdictions should confirm import licensing requirements before ordering.

A 12-month warranty from the date of shipment covers manufacturing defects and verifiable calibration non-conformance. Warranty claims are processed with return merchandise authorization (RMA); replacement units are dispatched within 5 business days of confirmed defect verification.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.