Bently Nevada 330703-000-040-10-02-00 Proximity Transducer – 3300 XL Series

Bently Nevada 330703-000-040-10-02-00 — 3300 XL 11 mm Eddy-Current Proximity Transducer in Rotating Machinery Protection Loops

The Bently Nevada 330703-000-040-10-02-00 is a factory-matched, 11 mm eddy-current proximity transducer belonging to the 3300 XL platform — a measurement architecture that has been the de facto standard for API 670-compliant machinery protection since its introduction. This specific configuration ships with a 1.0 m armored probe cable and carries FM/CSA intrinsic-safety approval (suffix -02-00), making it directly deployable in Division 1 / Zone 0 classified areas without additional barriers in many installations.

Within a turbomachinery protection loop, the 330703-000-040-10-02-00 occupies the sensing node of a three-component chain: probe → extension cable → Proximitor driver. The probe generates a high-frequency oscillating electromagnetic field (nominally 1.0 MHz carrier) that induces eddy currents in the conductive target shaft. As the air gap between probe tip and shaft surface changes — due to radial vibration, axial displacement, or thermal growth — the eddy-current loading on the oscillator circuit shifts, producing a DC-coupled output voltage that is linear across the calibrated gap range of 0.25 mm to 2.54 mm (10 to 100 mil). The matched Proximitor (3300 XL 11 mm series) demodulates this signal and delivers a buffered output of –1 VDC to –17 VDC at 200 mV/mil (7.87 V/mm) sensitivity, directly compatible with Bently Nevada 3300 XL and 3500 series monitor racks.

The 11 mm tip geometry is selected for medium-diameter shaft applications — typically 50 mm to 200 mm journal diameter — where the 8 mm probe would exhibit insufficient signal-to-noise margin and the 25 mm probe would introduce excessive sensitivity to surface irregularities. The probe body is constructed from 316L stainless steel with a PEEK (polyether ether ketone) tip housing, providing chemical resistance to turbine lube oils, seal gases, and process condensates across the full operating temperature envelope of –35 °C to +121 °C at the probe tip.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

Eddy-Current Oscillator Stability and EMC Architecture

The 3300 XL probe does not contain active electronics — all signal conditioning resides in the Proximitor driver module. The probe itself is a passive LC resonant element: the coil wound within the PEEK tip forms the inductive leg of the oscillator tank circuit, while the distributed capacitance of the coaxial cable forms the capacitive leg. This architecture eliminates active component failure modes at the probe tip, which is the highest-temperature, highest-vibration node in the measurement chain. The coil winding is encapsulated in a thermally stable epoxy compound rated to 150 °C, preventing coil movement under mechanical shock loads up to 500 g (per Bently Nevada environmental qualification testing).

Electromagnetic Compatibility (EMC) Design

The armored cable jacket provides a continuous Faraday shield from probe tip to Proximitor input, with shield termination at the driver end only — a single-point ground topology that eliminates ground-loop-induced noise. The shield is constructed from a double-layer braid (inner copper, outer stainless steel) with >95% optical coverage, attenuating external RF interference by a minimum of 40 dB across the 10 Hz – 100 MHz band. In installations near variable-frequency drives (VFDs) or high-current bus bars, this shielding architecture maintains output noise floor below 25 mV peak-to-peak — well within the 3500 monitor’s alarm threshold resolution of ±0.5 mil.

Thermal Compensation and Gap Stability

The probe tip assembly incorporates a thermally compensated coil former. As probe temperature rises, the thermal expansion coefficient of the PEEK housing (54 × 10⁻⁶ /°C) is mechanically counteracted by the stainless steel body (16 × 10⁻⁶ /°C), maintaining coil geometry within ±0.5% across the full –35 °C to +121 °C range. This passive compensation eliminates the need for software temperature correction in most turbomachinery applications, preserving measurement integrity during cold-start transients and full-load thermal stabilization cycles.

Intrinsic Safety Barrier Integration

The -02-00 approval suffix certifies this probe for use in the FM/CSA intrinsically safe system comprising the 3300 XL 11 mm Proximitor (part number 330180-X1-CN). The Proximitor limits fault energy to below the ignition threshold of Group IIC gases (hydrogen, acetylene) — the most stringent classification. No additional zener barriers are required between the Proximitor and the probe in this certified configuration, simplifying installation wiring and reducing potential failure points in the hazardous-area cable run.

System Integration Benefits

• Direct rack compatibility: Output signal is pre-conditioned to the –1 V to –17 V range required by Bently Nevada 3300 XL and 3500 series monitor input cards, eliminating signal conditioning adapters and associated latency.
• API 670 compliance out of the box: The matched probe-cable-Proximitor system meets the linearity, frequency response, and temperature requirements of API Standard 670 (5th Edition) for radial vibration, axial position, and differential expansion channels without field calibration adjustment.
• Deterministic frequency response to 10 kHz: The flat ±3 dB bandwidth from DC to 10,000 Hz captures sub-synchronous instabilities (oil whirl at 0.4–0.5×), synchronous 1× imbalance, and high-order blade-pass frequencies in a single measurement channel — no anti-aliasing filter adjustment required for standard turbomachinery speed ranges up to 60,000 RPM.
• Non-contacting measurement eliminates wear: Zero mechanical contact with the rotating shaft means sensor calibration drift is driven only by thermal and chemical exposure, not mechanical wear. Mean time between calibration (MTBC) in clean lube-oil environments typically exceeds 5 years.
• Emerson System 1 integration: The probe output feeds directly into System 1 Evolution software via the 3500 rack’s Ethernet gateway, enabling waveform capture, orbit plot generation, and trend analysis without additional signal conditioning hardware.
• Dual-use measurement capability: A single 330703-000-040-10-02-00 channel can simultaneously provide radial vibration (AC-coupled, filtered) and average shaft centerline position (DC component) to the monitor rack, reducing channel count and wiring cost in multi-bearing machines.
• Hazardous-area deployment without compromise: FM/CSA intrinsic-safety certification allows installation in Division 1 classified areas — including hydrogen-cooled generators and hydrocarbon compressor trains — without conduit seals or explosion-proof junction boxes on the probe cable run.
• Backward compatibility with legacy 3300 infrastructure: The 3300 XL probe is electrically and mechanically interchangeable with earlier 3300 series probes in the same tip-diameter class, allowing direct replacement in existing installations without monitor reconfiguration or re-gapping.
• Diagnostic transparency via gap voltage monitoring: The DC bias voltage at the monitor’s buffered output provides a continuous, real-time indication of probe-to-shaft gap. Operators can detect probe fouling, shaft eccentricity changes, and bearing wear trends by trending this DC value — no additional instrumentation required.
• Reduced commissioning time: Factory-matched and factory-calibrated as a system (probe + cable + Proximitor), the 330703-000-040-10-02-00 arrives with a calibration certificate traceable to NIST standards, eliminating field calibration loops during plant commissioning.

Quality Assurance & Global Logistics

Every Bently Nevada 330703-000-040-10-02-00 unit supplied through siemensplc.com is sourced from verified Emerson / Bently Nevada authorized distribution channels or traceable surplus inventory with full documentation. Prior to dispatch from our Xiamen, China facility, each unit undergoes a structured incoming inspection protocol:

• Visual inspection of probe tip, cable jacket, and MIL-C-5015 connector for mechanical damage or corrosion
• Part number label verification against purchase documentation and CoC
• Coil continuity and insulation resistance check (probe coil to shield, minimum 100 MΩ at 500 VDC)
• Cable shield continuity end-to-end verification
• Dimensional check of probe tip diameter and thread specification (M14×1.5 standard)
• Certificate of Conformance (CoC) and, where available, original factory calibration data sheet included with shipment

Xiamen is a designated free-trade port with direct air freight connections to major industrial hubs: Frankfurt, Houston, Singapore, Dubai, and Tokyo. Standard export packaging uses anti-static foam-lined cases with desiccant packs, maintaining storage conditions per Bently Nevada’s recommended 15 °C – 35 °C, <70% RH shelf-storage specification. Typical dispatch lead time for in-stock units is 1–3 business days from order confirmation, with DHL Express, FedEx International Priority, and UPS Worldwide Expedited available as carrier options. DDP (Delivered Duty Paid) and DAP (Delivered At Place) Incoterms are both supported. Export compliance review (EAR/ECCN classification) is completed prior to each international shipment.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.