Bently Nevada 330903-17-19-05-02-00 Proximity Probe – NSv Series

Bently Nevada 330903-17-19-05-02-00 NSv Eddy-Current Proximity Probe — Shaft Displacement Measurement in Critical Rotating Machinery

The Bently Nevada 330903-17-19-05-02-00 is a 5 mm eddy-current proximity probe belonging to the NSv (Non-contacting Vibration) product family. Its primary function within a machinery protection loop is to convert the physical gap between the probe tip and a conductive target shaft into a proportional DC voltage signal, delivering continuous, non-contact measurement of radial shaft vibration and static position. The probe operates as the field-sensing element in a three-component measurement chain — probe, extension cable, and Proximitor® driver — and its electrical characteristics are factory-matched to that chain to ensure system-level calibration accuracy without field adjustment.

In a typical steam turbine or centrifugal compressor installation, two probes are mounted 90° apart in the X–Y plane at each bearing journal. The differential voltage outputs feed directly into a 3500-series monitor card, which computes shaft orbit, 1× and 2× vibration vectors, and DC gap voltage in real time. Any deviation beyond the configured alert or danger setpoints triggers relay outputs to the machine protection system within the monitor’s scan cycle — typically under 20 ms. This deterministic response latency is a fundamental requirement of API 670 machinery protection architecture, and the 330903-17-19-05-02-00 is designed and calibrated to support it without introducing measurement uncertainty at the sensor level.

The probe body is machined from stainless steel with a PEEK (polyether ether ketone) tip housing, providing chemical resistance against lubricating oils, seal gases, and process condensates encountered in turbomachinery bearing housings. The M10 × 1.0 thread allows direct installation into standard API 670-compliant probe holders without adapter hardware. The 5 m integral cable terminates in a 2-pin MIL-C-5015 style connector, which mates with Bently Nevada 330130-series extension cables to reach the Proximitor® driver mounted outside the hazardous zone.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The operating principle of the 330903-17-19-05-02-00 is based on the Lenz’s law induction effect. The Proximitor® driver supplies a high-frequency oscillating current — nominally 1.0 MHz — through the probe’s internal coil. When the coil approaches a conductive target, eddy currents are induced on the target surface, loading the oscillator circuit and reducing its amplitude. The driver’s demodulation stage converts this amplitude change into a DC voltage proportional to the probe-to-target gap. The 330903-17-19-05-02-00 is factory-calibrated as a matched set with its designated extension cable and Proximitor® driver, meaning the coil impedance, cable capacitance, and driver gain constants are characterized together — not independently — to achieve the specified ±0.5% scale factor accuracy across the full linear range.

EMC Design: The integral cable incorporates a double-layer foil-and-braid shield with 95% optical coverage, terminated at both ends to the connector shell. This construction attenuates radiated interference from variable-frequency drives, high-voltage bus bars, and RF sources common in turbine halls. The shield drain wire is grounded at the Proximitor® driver end only, preventing ground loop currents from appearing as low-frequency noise on the measurement signal — a critical design detail in installations where the machine casing and control room ground references differ by several millivolts.

Thermal Stability: The PEEK tip housing has a coefficient of thermal expansion (CTE) of approximately 50 µm/m·°C, significantly lower than standard nylon or epoxy alternatives. This dimensional stability ensures that the probe’s effective sensing face geometry does not shift measurably across the −35°C to +177°C operating envelope, preserving calibration integrity in hot-section bearing pedestals where ambient temperatures can cycle by 100°C or more during startup and shutdown sequences.

Mechanical Robustness: The M10 × 1.0 fine-pitch thread provides a higher thread engagement surface area per unit axial length compared to coarser thread forms, reducing the risk of probe loosening under the vibration loads present at bearing housings. The stainless steel body resists corrosion from oil mist, steam condensate, and cleaning solvents used during maintenance outages.

System Integration Benefits

• Direct API 670 Compliance: The probe’s scale factor, linear range, and connector interface conform to API 670 5th Edition requirements, allowing it to be specified in machinery protection system documentation without deviation notes or engineering waivers.
• Matched-Set Calibration: Factory calibration as a probe-cable-driver set eliminates the field calibration step required when mixing components from different serial number batches, reducing commissioning time at site.
• Backward Compatibility with 3300 XL Infrastructure: The 330903-17-19-05-02-00 is electrically compatible with existing 3300 XL Proximitor® drivers and 3500-series monitor cards, enabling direct replacement of legacy probes without firmware updates or I/O reconfiguration.
• Deterministic Signal Latency: The eddy-current measurement chain introduces no digital processing delay at the probe level. The analog output reaches the monitor card’s A/D converter within the cable propagation time, supporting the sub-20 ms trip response required by API 670 for overspeed and high-vibration protection.
• Diagnostic Transparency via Gap Voltage: The DC gap voltage output provides a continuous, independent indicator of probe installation gap. Operators can monitor gap drift over time to detect probe loosening, target surface wear, or bearing clearance changes without removing the probe from service.
• Hazardous Area Deployment: ATEX Zone 1 and IECEx-certified variants are available for installations in gas-group IIC environments, including hydrogen-cooled generators and LNG compressor trains, without requiring additional intrinsic safety barriers when used with the appropriate certified Proximitor® driver.
• Orbit and Vector Analysis Support: The probe’s flat frequency response from DC to beyond 10 kHz supports full shaft orbit computation, 1× synchronous vector tracking, and sub-synchronous instability detection — all standard diagnostic functions in Bently Nevada System 1 software.
• Reduced Maintenance Interval: The IP67 rating and PEEK tip construction allow the probe to remain installed through water-wash cleaning cycles and steam purging operations, reducing the number of probe pull-and-inspect events required during planned maintenance outages.

Quality Assurance & Global Logistics

Every 330903-17-19-05-02-00 unit supplied by siemensplc.com is sourced through verified industrial distribution channels with full traceability to Bently Nevada (Baker Hughes) manufacturing documentation. Pre-shipment inspection covers part number label verification against OEM packaging standards, connector pin integrity check, cable jacket visual inspection for abrasion or kinking, and CoC (Certificate of Conformance) documentation review where available. Units that do not pass inspection are quarantined and not dispatched.

Logistics operations are based in Xiamen, China, with direct access to Xiamen Gaoqi International Airport and Xiamen Port, supporting both air freight and sea freight consolidation. Standard export shipments are dispatched via DHL Express, FedEx International Priority, or UPS Worldwide Expedited, with transit times of 3–5 business days to most destinations in Southeast Asia, the Middle East, Europe, and the Americas. Full export documentation — commercial invoice, packing list, and certificate of origin — is prepared for each shipment. HS code classification and customs value declaration are handled by our logistics team to minimize clearance delays at destination ports.

For shutdown and turnaround situations requiring same-day or next-flight-out dispatch, contact our team directly via WhatsApp at +86 18359268345 to confirm stock availability and arrange priority handling. All shipments under the 12-month warranty are eligible for replacement or credit in the event of a verified manufacturing defect.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.