Bently Nevada 330904-00-04-05-02-00 Proximity Transducer – 3300 XL Series

Bently Nevada 330904-00-04-05-02-00 — 8 mm Eddy-Current Proximity Transducer in Rotating Machinery Protection Loops

The Bently Nevada 330904-00-04-05-02-00 is an 8 mm eddy-current proximity transducer belonging to the 3300 XL Series, engineered for continuous, non-contact measurement of radial shaft vibration, axial position, and eccentricity in high-speed rotating machinery. Within a machinery protection architecture, this transducer occupies the first node of the signal chain: it converts mechanical displacement into a proportional DC voltage that feeds directly into a 3300 XL or 3500 Series monitor rack. The accuracy and repeatability of every downstream alarm, trip, and trend record depends entirely on the dimensional and electrical integrity of this probe assembly.

The 330904-00-04-05-02-00 configuration encodes a specific physical and electrical build: 8 mm probe tip diameter, 0.5 m integral armored cable, 5.0 m extension cable, standard industrial connector, and CE marking. This part number is validated for use with the 3300 XL NSv Proximitor (330780-90-00) and the 3300 XL 8 mm Proximitor driver family. Substituting a non-XL driver will shift the sensitivity curve and produce systematic measurement error across the full operating range.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

Eddy-Current Operating Principle and Coil Architecture
The probe tip houses a precision-wound coil driven by a high-frequency oscillator (typically 1.0 MHz carrier) within the paired Proximitor. When the probe tip approaches a conductive target, eddy currents are induced on the target surface, loading the coil and reducing its Q-factor. The Proximitor demodulates this impedance change into a DC voltage proportional to gap distance. The 8 mm tip diameter of the 330904 series provides a linear measurement range of 2.0 mm — a deliberate balance between spatial resolution and the physical shaft diameters encountered in turbomachinery (typically 50–300 mm journals).

EMC Design and Shielding Architecture
The integral 0.5 m cable uses a triaxial construction: the center conductor carries the oscillator signal, the inner shield is driven at the same potential as the center conductor (guard drive), and the outer shield is grounded at the Proximitor end only. This driven-guard topology eliminates capacitive leakage between the coil and the cable shield, preserving measurement accuracy over the full 5.5 m total cable run. The armored outer jacket provides mechanical protection and additional RF shielding in environments with variable-frequency drives (VFDs) or high-current bus bars in proximity.

Temperature Compensation
The probe coil’s inductance and the extension cable’s distributed capacitance both exhibit temperature coefficients. Bently Nevada’s 3300 XL system compensates for these effects through matched calibration: each probe-cable-driver set is characterized as a system, not as individual components. The −35 °C to +177 °C probe rating covers bearing housing temperatures in steam turbines operating at inlet conditions up to 600 °C, where the probe is mounted in a cooled bracket assembly. Exceeding the cable temperature limit (85 °C) without thermal isolation will introduce a systematic sensitivity shift of approximately 0.3–0.5% per 10 °C above the rated limit.

Mechanical Mounting and Gap Setting
The probe body is threaded (M10 × 1.0 mm pitch standard) for direct installation into a machined bracket. The nominal installation gap for the 330904 series is 1.0 mm (−10.4 VDC output), placing the operating point at the center of the 0.25–2.25 mm linear range. This center-gap strategy maximizes the usable dynamic range for both positive and negative shaft excursions, which is critical for API 670-compliant radial vibration monitoring where the full-scale alarm threshold is typically set at 125 µm (5 mil) peak-to-peak.

System Integration Benefits

• Direct API 670 compliance: The 330904-00-04-05-02-00 is factory-calibrated against AISI 4140 steel per API 670 Annex D, eliminating the field calibration step required for non-compliant probes and reducing commissioning time by 2–4 hours per measurement point.
• Plug-and-play monitor compatibility: Validated for use with Bently Nevada 3500/42M, 3500/45, and 3500/46M monitor cards without driver re-tuning. Replacement during an unplanned outage requires only gap re-setting — no software reconfiguration.
• Preserved System 1 trend baselines: Consistent 7.87 V/mm sensitivity across production lots ensures that historical vibration trend data in System 1 / Orbit 60 software remains statistically valid after probe replacement. Sensitivity variation between lots is controlled to ±1% of nominal.
• Deterministic alarm response: The analog output path from probe to monitor card introduces less than 1 ms of signal latency, supporting the 3500 rack’s 20 ms trip response time for overspeed and high-vibration protection loops.
• Diagnostic transparency via DC gap voltage: The Proximitor’s DC output provides a continuous, passive indication of probe-to-shaft gap. A technician can verify probe health and installation gap with a standard voltmeter without interrupting the measurement loop — a significant advantage during live machinery inspections.
• Hazardous-area pathway: The -02-00 CE-marked variant can be upgraded to the -05-00 ATEX/IECEx variant for Zone 1/Zone 2 installations without changing the monitor rack configuration, provided the Proximitor barrier is also rated for the target zone.
• Multi-protocol DCS integration: The 3500 rack’s analog output (4–20 mA) and optional Modbus RTU/TCP or PROFIBUS DP modules allow the 330904’s displacement signal to be integrated into ABB 800xA, Honeywell Experion, Emerson DeltaV, and Yokogawa CENTUM VP without additional signal conditioning hardware.
• Reduced spare-parts inventory complexity: The 3300 XL probe family uses a common Proximitor driver across 5 mm, 8 mm, and 11 mm probe diameters (with appropriate calibration files), allowing a single driver spare to cover multiple measurement point types in a mixed-probe installation.

Quality Assurance & Global Logistics

Every Bently Nevada 330904-00-04-05-02-00 unit supplied by siemensplc.com is sourced through verified distribution channels and undergoes a structured incoming inspection protocol before dispatch from our Xiamen, China facility.

Inspection Protocol: Each unit is verified for coil continuity and insulation resistance, connector pin integrity and torque, cable jacket condition and shield continuity, and sensitivity output at a reference gap using a calibrated test fixture. Units that deviate more than 1% from the nominal 7.87 V/mm sensitivity are quarantined and returned to the supplier.

Documentation Package: Shipments include the original Bently Nevada factory calibration certificate, original OEM packaging with lot traceability, commercial invoice with HS code 9031.80.90.90, and a packing list suitable for customs clearance in EU, US, Southeast Asian, and Middle Eastern markets.

Logistics: In-stock units ship within 1–3 business days from Xiamen via DHL Express, FedEx International Priority, or UPS Worldwide Expedited. Transit times to major industrial hubs: Europe 3–5 days, North America 4–6 days, Southeast Asia 2–3 days, Middle East 4–5 days. Emergency outage shipments can be arranged with same-day dispatch for orders confirmed before 14:00 CST.

Warranty: 12-month warranty against manufacturing defects from the date of shipment. Defective units are replaced or refunded in full. Warranty claims require photographic documentation of the defect and the original shipping label.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.