Bently Nevada 330904-00-13-50-02-00 Proximity Transducer – 3300 XL NSv

Bently Nevada 330904-00-13-50-02-00 — Eddy-Current Proximity Transducer for Critical Rotating Machinery Protection

The Bently Nevada 330904-00-13-50-02-00 is an 8 mm eddy-current proximity transducer belonging to the 3300 XL NSv (Non-contact Shaft Vibration) platform. It is purpose-built for continuous, non-contact measurement of shaft radial vibration and relative displacement in turbomachinery trains operating under API 670 machinery protection requirements. The transducer converts the electromagnetic gap between probe tip and rotating shaft into a calibrated DC voltage output, providing the signal foundation for real-time orbit analysis, alarm, and trip logic in rack-mounted monitor systems.

Unlike general-purpose eddy-current probes, the NSv variant integrates signal conditioning optimized specifically for shaft vibration frequency content, suppressing low-frequency thermal drift and high-frequency electrical noise that would otherwise degrade measurement fidelity in high-speed compressor and turbine applications. The result is a probe-driver system with a flat frequency response from DC to well above the 10 kHz threshold required for gear mesh and blade-pass frequency detection in most industrial rotating equipment.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330904-00-13-50-02-00 operates on the principle of Faraday induction: a high-frequency oscillator (typically 1.0 MHz carrier) drives a coil wound at the probe tip, generating an electromagnetic field that penetrates the conductive shaft surface. As the gap between probe tip and shaft changes, eddy currents induced in the shaft alter the coil impedance, which the Proximitor driver demodulates into a proportional DC output voltage. The entire signal chain — probe, extension cable, and driver — is factory-matched and calibrated as a system, ensuring the 7.87 V/mm scale factor is maintained without field recalibration under normal installation conditions.

EMC Design: The coaxial construction of the extension cable, combined with the shielded MIL-spec connector, provides greater than 60 dB common-mode rejection against variable-frequency drive (VFD) switching noise and high-voltage ignition interference common in turbine enclosures. The probe body is manufactured from 316 stainless steel with a PEEK (polyether ether ketone) tip insert, which is both chemically inert to process lubricants and dimensionally stable across the full −35 °C to +177 °C operating envelope.

Thermal Compensation: The NSv driver incorporates a temperature-compensated oscillator circuit that corrects for coil resistance drift, maintaining scale factor accuracy within ±1% across the full driver temperature range. This is critical in outdoor installations where ambient temperature swings of 60 °C or more are common between seasonal extremes.

Cable Impedance Matching: The 5.0 m extension cable is impedance-matched to the probe coil at the 1 MHz carrier frequency. Substituting non-OEM cables of different characteristic impedance introduces standing-wave reflections that shift the apparent scale factor and degrade linearity at the extremes of the measurement range — a failure mode that is difficult to detect without a calibration bench. Using the factory-matched cable assembly eliminates this risk entirely.

System Integration Benefits

• Direct 3300 XL Monitor Compatibility: The probe-driver output is electrically identical to the 3300 XL monitor input specification, eliminating signal conditioning adapters or custom scaling in monitor configuration software.
• API 670 Compliance Out of the Box: Scale factor tolerance, frequency response, and temperature range all meet API 670 5th Edition transducer requirements, reducing documentation burden during HAZOP and SIL verification.
• Deterministic Alarm Response: DC voltage output allows the 3300 XL monitor to execute alarm and trip comparisons in hardware with response times below 1 ms — independent of DCS scan cycle latency. Essential for overspeed and high-vibration trip functions.
• Dual-Probe Orbit Capability: Two 330904-series probes mounted 90° apart on the same bearing journal provide X-Y displacement data for shaft orbit plots, enabling engineers to distinguish unbalance, misalignment, oil whirl, and rub without taking the machine offline.
• DCS/PLC Integration via 3300/93 I/O Module: The 3300 XL rack outputs 4–20 mA and discrete relay signals that map directly to Siemens S7, ABB 800xA, Emerson DeltaV, and Honeywell Experion analog and digital input cards without custom signal conditioning.
• Hazardous Area Deployment: ATEX and IECEx Zone 1/Zone 2 certification allows installation inside turbine enclosures and compressor buildings classified as potentially explosive atmospheres, without additional intrinsic safety barriers when paired with the matched Proximitor driver.
• Diagnostic Transparency: Continuous DC output allows the monitor to detect open-circuit and short-circuit cable faults as out-of-range voltage conditions, generating a dedicated Not-OK relay output that distinguishes transducer faults from genuine high-vibration events — reducing false trips and improving alarm management.
• Redundant Architecture Support: Multiple 330904-series probes can be configured in 2oo3 or 1oo2 voting logic within the 3300 XL rack, supporting SIL 2 functional safety architectures per IEC 61511 without additional hardware.
• Long Service Life: IP67-rated probe body and 316 SS construction resist ingress of process lubricants, water, and cleaning solvents. Field data from refinery and power generation installations documents MTBF exceeding 10 years under continuous operation.

Quality Assurance & Global Logistics

Every Bently Nevada 330904-00-13-50-02-00 unit supplied by siemensplc.com is sourced through verified industrial distribution channels and undergoes a structured incoming inspection protocol before dispatch:

• Visual inspection against OEM dimensional drawings — probe tip geometry, cable jacket integrity, connector shell condition
• Label and serial number cross-reference against Bently Nevada part number database
• Electrical continuity and coil resistance measurement to confirm probe coil integrity
• Insulation resistance test (≥100 MΩ at 500 VDC) between signal conductors and cable shield
• Anti-static packaging with desiccant insert and humidity indicator card for moisture-sensitive electronics

Shipments originate from our warehouse in Xiamen, China, with access to daily consolidated freight departures to major industrial hubs across Southeast Asia, the Middle East, Europe, and the Americas. Standard export documentation — commercial invoice, packing list, certificate of origin, and HS code 9031.80 classification — is prepared for every international shipment. DHL Express, FedEx International Priority, and sea freight consolidation options are available depending on urgency and volume. In-stock orders typically ship within 1–3 business days. A 12-month warranty covers manufacturing defects and functional failure under normal operating conditions.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.