Bently Nevada 330905-00-08-10-01-00 Proximity Probe – 3300 XL Series

Bently Nevada 330905-00-08-10-01-00 — 8 mm Eddy Current Proximity Probe for Rotating Machinery Protection

The Bently Nevada 330905-00-08-10-01-00 is an 8 mm eddy current proximity probe belonging to the 3300 XL Proximity Transducer System. It performs continuous, non-contact measurement of radial shaft vibration, axial position, and differential shaft expansion in turbomachinery and other critical rotating equipment. The probe operates on the eddy current principle: a high-frequency oscillator within the paired driver generates an electromagnetic field at the probe tip; when a conductive target surface enters this field, eddy currents are induced, loading the oscillator and producing a DC output voltage proportional to the gap distance. This mechanism delivers sub-micron resolution without any mechanical contact, eliminating wear-related drift over the service life of the installation.

Within a complete 3300 XL transducer loop, the 330905-00-08-10-01-00 probe connects via a 1.0 m integral cable to a 9.0 m extension cable (total system cable: 10 m), which then terminates at a compatible 3300 XL 8 mm driver/oscillator-demodulator. The driver conditions the raw oscillator signal into a calibrated DC voltage output, typically –1 VDC to –17 VDC, which feeds directly into Bently Nevada 3500 Series monitor cards or equivalent machinery protection systems. The entire signal chain is factory-calibrated as a matched set to maintain the rated sensitivity of 7.87 V/mm (200 mV/mil) across the linear measurement range of 0.25 mm to 2.54 mm (10 to 100 mil).

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330905-00-08-10-01-00 probe body is machined from 316 stainless steel, providing corrosion resistance in environments exposed to process gases, lubricating oils, and condensate. The tip assembly houses a precision-wound sensing coil encapsulated in a thermally stable polymer compound rated to 177°C, which preserves coil geometry and inductance under sustained thermal cycling — a failure mode common in lower-grade proximity probes where coil deformation shifts the calibration curve.

The integral coaxial cable uses a low-loss, impedance-controlled construction with a braided shield terminated at both ends to the probe housing and the extension cable connector. This shielding architecture attenuates capacitively coupled interference from adjacent power cables and variable-frequency drives, which are prevalent in turbomachinery enclosures. The cable jacket is rated for continuous immersion in lubricating oil and intermittent exposure to steam, consistent with bearing housing environments in steam turbines and centrifugal compressors.

From an EMC standpoint, the 3300 XL system architecture places the oscillator circuit inside the driver module rather than at the probe tip. This design decision keeps the active, noise-susceptible electronics away from the high-temperature, high-vibration zone at the bearing housing. The probe itself is a passive inductive element, which means it has no active components that can fail due to thermal stress or electromagnetic transients at the measurement point. The driver module, located in the instrument cabinet, operates in a controlled environment and can be replaced without disturbing the probe installation — a significant maintenance advantage in continuous-process plants where unplanned shutdowns carry substantial cost.

The calibration of the 330905-00-08-10-01-00 is performed as a matched system with its paired extension cable and driver. The sensitivity figure of 7.87 V/mm is traceable to NIST-referenced standards and is documented on the calibration certificate shipped with each unit. Substituting unmatched components — for example, using a different cable length or a driver from a different calibration batch — introduces a systematic sensitivity error that cannot be corrected by monitor scale factor adjustment alone. This is a critical integration constraint that field engineers must observe during spare-parts management.

System Integration Benefits

• Direct API 670 compliance: The 3300 XL system meets API 670 Fourth Edition requirements for radial vibration, axial position, and differential expansion channels, simplifying machinery protection system documentation for new installations and audits.
• Deterministic signal latency: The analog DC output of the driver delivers a continuous, real-time signal with no digitization delay at the transducer level. Monitor cards sample this signal at rates up to 20 kHz, preserving sub-synchronous vibration components that digital fieldbus transducers may alias or filter.
• Plug-compatible with 3500 Series monitors: The –1 to –17 VDC output range is directly accepted by Bently Nevada 3500/40M, 3500/42M, and 3500/45 monitor cards without signal conditioning adapters, reducing wiring complexity and potential failure points.
• Non-contact measurement eliminates mechanical loading: Unlike contact-type displacement sensors, the eddy current probe exerts zero force on the shaft, making it suitable for lightweight rotors where contact-induced deflection would corrupt the measurement.
• Wide thermal operating range supports hot-section installations: The –35°C to +177°C probe rating covers bearing housing temperatures in gas turbines, steam turbines, and high-speed compressors without requiring thermal isolation standoffs.
• Integral cable reduces connector count: The 1.0 m integral cable eliminates one coaxial connector junction at the probe body, reducing the number of impedance discontinuities in the signal path and lowering the probability of connector-related signal degradation in high-vibration environments.
• Diagnostic transparency via gap voltage monitoring: The DC output voltage at the driver output serves as a direct, real-time indicator of probe-to-shaft gap. Operators can verify correct probe installation and detect shaft centerline shifts without additional instrumentation, using only a calibrated voltmeter at the driver output terminals.
• Hazardous area certification: ATEX and FM certifications at the system level permit installation in Zone 1/Division 1 classified areas, covering the majority of oil and gas processing and petrochemical plant environments without requiring additional intrinsic safety barriers in standard configurations.

Quality Assurance & Global Logistics

Every Bently Nevada 330905-00-08-10-01-00 unit dispatched from our Xiamen, China facility is sourced through verified industrial supply channels and subjected to a structured pre-shipment inspection protocol. Physical inspection covers the probe housing, tip condition, cable jacket integrity, and connector seating. Electrical verification confirms coaxial continuity, insulation resistance between the center conductor and shield, and the absence of open or short-circuit conditions. Units that do not pass all inspection criteria are quarantined and not offered for sale.

Shipments originate from Xiamen, China, with access to DHL Express, FedEx International Priority, and UPS Worldwide Expedited services. Standard international transit times range from 3 to 7 business days for major industrial hubs in Europe, Southeast Asia, the Middle East, and the Americas. Full export documentation — including commercial invoice, packing list, and certificate of origin — is prepared for every shipment. HS Code 9031.80 (precision measuring instruments) is applied consistently to facilitate customs clearance. For bulk procurement or project-based orders, sea freight consolidation and door-to-door logistics coordination are available upon request.

All units are covered by a 12-month warranty from the date of shipment. Warranty claims are handled directly by our technical team, with replacement units dispatched within 5 business days of confirmed defect verification. Warranty coverage applies to manufacturing defects and verified functional failures under normal operating conditions as defined in the Bently Nevada 3300 XL installation manual.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.