Bently Nevada 330910-00-25-10-01-00 Proximity Transducer – 3300 XL NSv

Bently Nevada 330910-00-25-10-01-00 — Eddy-Current Proximity Transducer for Critical Rotating Machinery Protection

The Bently Nevada 330910-00-25-10-01-00 is a 25-foot (7.62 m) eddy-current proximity transducer belonging to the 3300 XL NSv Series — a platform engineered specifically for continuous, non-contact displacement and vibration measurement on rotating shafts in high-consequence industrial environments. Within a machinery protection loop, this transducer occupies the first and most critical node: it converts mechanical shaft displacement into a proportional DC voltage signal that feeds downstream Proximitor sensors, signal conditioners, and rack-mounted monitors. The accuracy and linearity of this conversion directly determines the fidelity of every alarm, trip, and diagnostic event generated by the protection system.

Unlike piezoelectric accelerometers that measure surface acceleration, the eddy-current transducer operates on electromagnetic induction principles. A high-frequency oscillator — typically 1.0 MHz — drives a coil wound at the transducer tip. When the conductive target shaft enters the electromagnetic field, eddy currents are induced on the shaft surface, loading the oscillator circuit and producing a measurable impedance shift. The Proximitor electronics convert this impedance change into a linear DC voltage output of −18 VDC nominal at the calibrated gap, with a sensitivity of 200 mV/mil (7.87 V/mm). This architecture enables DC-coupled measurement from 0 Hz (true static position) through 10,000 Hz dynamic vibration — a bandwidth that covers all relevant shaft dynamic phenomena including subsynchronous instability, synchronous unbalance, and high-frequency rubs.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 330910-00-25-10-01-00 is a passive transducer element — it contains no active electronics. Its functional integrity depends on three tightly controlled physical parameters: coil inductance, cable characteristic impedance, and tip geometry. Bently Nevada manufactures the sensing coil to a controlled inductance tolerance, ensuring that when paired with the designated 3300 XL 8 mm Proximitor sensor (e.g., 330180 series), the complete system achieves the published sensitivity and linearity without field calibration adjustment.

The 25-foot integral cable is a matched coaxial assembly with a defined capacitance-per-foot specification. Substituting non-OEM cables of differing capacitance shifts the oscillator operating point, introducing gain error and nonlinearity that cannot be corrected at the monitor level. This is a fundamental constraint of the eddy-current measurement architecture — the transducer, extension cable, and Proximitor form a single calibrated system, not interchangeable components.

From an EMC standpoint, the coaxial cable construction provides inherent shielding against radially coupled electric field interference. The shield is grounded at the Proximitor end only (single-point grounding), preventing ground loop currents that would appear as low-frequency noise on the output signal. In environments with high magnetic field density — such as near large motor stators or transformer banks — the transducer tip’s ferrite-loaded housing attenuates stray flux coupling, preserving measurement integrity at the sub-mil resolution level.

The −24 VDC supply architecture (delivered through the Proximitor) means the transducer cable carries only the oscillator drive signal and the demodulated DC output — both at signal levels well below the threshold for arc discharge or insulation stress. This design choice simplifies hazardous-area classification: the transducer itself is intrinsically safe when used with an approved Proximitor and associated apparatus, enabling deployment in Zone 1 / Division 1 classified areas without additional barriers in many configurations.

System Integration Benefits

• DC-coupled measurement path: The 0 Hz lower frequency limit enables simultaneous static position (thrust position, rotor centerline) and dynamic vibration measurement from a single transducer installation, eliminating the need for separate position sensors in many API 670 channel configurations.
• Deterministic signal latency: The analog output path from transducer tip to Proximitor output introduces no digital processing delay. Signal latency is governed only by the Proximitor’s demodulation filter time constant — typically <1 ms — ensuring that protection system trip response times remain within API 670 requirements.
• Direct compatibility with 3500 series monitors: The −18 VDC nominal output and 200 mV/mil sensitivity are natively recognized by Bently Nevada 3500/40M, 3500/42M, and 3500/45 monitor modules without scaling configuration, reducing commissioning time and eliminating scaling errors.
• Keyphasor synchronization: When used alongside a 3300 XL Keyphasor transducer on the same shaft, the 330910-00-25-10-01-00 provides the vibration vector data required for synchronous tracking analysis (1X, 2X amplitude and phase), enabling precise identification of unbalance, misalignment, and resonance conditions.
• Diagnostic transparency via gap voltage monitoring: The DC component of the Proximitor output provides a continuous, real-time indication of average shaft position. Trending this gap voltage over time reveals bearing wear, thermal growth, and rotor bow — failure modes that are invisible to vibration-only monitoring systems.
• Redundant channel architecture support: The transducer’s compact 8 mm tip diameter allows dual-probe installations at 90° orientation within standard bearing housings, supporting XY vibration measurement for full orbital analysis and redundant protection channel configurations per API 670 Section 5.
• Wide temperature operating envelope: The −35 °C to +121 °C range covers outdoor installations in arctic climates as well as bearing housing proximity in high-temperature turbine applications, without requiring thermal management accessories.
• Non-contact sensing eliminates mechanical wear: With no physical contact between the transducer tip and the rotating shaft, the sensor has no inherent wear mechanism. Mean time between replacement is governed by cable fatigue and connector integrity rather than sensing element degradation, supporting multi-year maintenance intervals in stable installations.

Quality Assurance & Global Logistics

Every Bently Nevada 330910-00-25-10-01-00 unit supplied through siemensplc.com is sourced from verified supply channels and subjected to a structured pre-shipment inspection protocol. Visual examination covers label authenticity, coaxial connector pin geometry, cable sheathing continuity, and housing marking conformance against Bently Nevada factory documentation. Functional verification confirms output voltage at the nominal gap and cable continuity across the full 25-foot length. Units that do not pass inspection are quarantined and not offered for sale.

Logistics operations are managed from Xiamen, China — a major southeastern port city with direct access to international express freight networks. Standard dispatch lead time for in-stock units is 1–2 business days from order confirmation. Shipping options include DHL Express, FedEx International Priority, and UPS Worldwide Expedited, with typical transit times of 3–7 business days to Asia-Pacific destinations and 5–10 business days to Europe and the Americas. All international shipments are accompanied by a commercial invoice, packing list, and certificate of origin to facilitate customs clearance. Export classification and HS code documentation are prepared in accordance with Chinese customs regulations and destination country import requirements.

A 12-month warranty covers functional defects attributable to manufacturing or material non-conformance. Warranty claims are processed through direct communication with our technical team — no third-party RMA routing. For volume procurement or project-based sourcing requirements, framework agreements with defined lead times and pricing are available upon request.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.