Bently Nevada 330930-040-00-05 Proximity Extension Cable – 3300 XL

Bently Nevada 330930-040-00-05 — 5-Meter Coaxial Extension Cable for 3300 XL Proximity Transducer Systems

The 330930-040-00-05 is a factory-terminated, armor-jacketed coaxial extension cable manufactured by Bently Nevada for exclusive use within the 3300 XL Proximity Transducer System. Its function is singular and non-negotiable in the measurement chain: it bridges the proximity probe tip to the Proximitor® sensor while preserving the calibrated electrical characteristics upon which the entire vibration measurement depends. The length code 040 designates a 4.0 m extension segment; combined with the probe’s integral cable, the total system cable length reaches the 5.0 m (16.4 ft) value required to match the Proximitor® sensor’s factory-calibrated gap range and scale factor of 7.87 V/mm (200 mV/mil).

This cable is not a generic coaxial assembly. Its dielectric geometry, conductor gauge, and termination impedance are matched to the 3300 XL eddy-current driver circuit. Substituting an off-the-shelf coaxial cable — even one with nominally identical dimensions — will introduce impedance discontinuities that shift the output voltage-to-gap relationship, producing systematic measurement error that cannot be corrected by software offset alone.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 3300 XL proximity transducer system operates on the eddy-current principle: a high-frequency oscillator within the Proximitor® sensor drives a radio-frequency signal through the coaxial cable to the probe tip coil. The coil generates an electromagnetic field; when a conductive target (shaft) enters this field, eddy currents are induced, loading the oscillator and reducing the output voltage in a linear relationship to gap distance. The integrity of this measurement depends entirely on the transmission-line characteristics of the cable path.

Impedance Continuity: The 330930-040-00-05 is manufactured to a controlled characteristic impedance matched to the 3300 XL driver circuit. Any impedance mismatch — caused by a non-OEM cable, a damaged connector, or an unauthorized field splice — creates a reflection coefficient at the discontinuity point. At the operating frequency of the eddy-current oscillator (typically in the low-MHz range), even a small reflection alters the apparent load seen by the Proximitor® and shifts the output voltage-to-gap curve, introducing a systematic offset error that cannot be nulled by the monitor’s gap alarm setpoints.

EMC Shielding Architecture: The stainless steel armor jacket provides a continuous, low-impedance shield from the probe connector to the Proximitor® input. In turbomachinery environments — where variable-frequency drives, high-current bus bars, and ignition systems generate broadband electromagnetic interference — an unbroken shield is the primary defense against common-mode noise injection into the measurement signal. The armor also provides mechanical protection against abrasion, oil mist ingress, and the cyclic mechanical stress imposed by vibrating pipe racks and cable trays.

Thermal Stability: The low-loss dielectric material used in the cable construction maintains its permittivity across the rated –55 °C to +125 °C range. Dielectric constant drift with temperature would alter the cable’s propagation velocity and effective electrical length, producing a temperature-dependent scale factor error. The OEM dielectric specification eliminates this variable from the measurement uncertainty budget.

Connector Termination Integrity: Factory termination under controlled conditions ensures that the center conductor, dielectric, and outer shield are mechanically and electrically continuous at the connector interface. Field-terminated connectors, even when assembled by skilled technicians, introduce variability in contact resistance and dielectric gap at the termination point — both of which affect the high-frequency signal path.

System Integration Benefits

• Calibration Traceability Preserved: Using the OEM-specified 330930-040-00-05 maintains the factory calibration chain from Proximitor® sensor to probe tip. No field recalibration is required after a like-for-like cable replacement, reducing maintenance downtime to the time required for physical swap-out and gap verification.
• API 670 Compliance Maintained: API 670 (Machinery Protection Systems) mandates that proximity transducer systems be installed and maintained as matched, calibrated sets. Substituting a non-OEM cable invalidates the system’s compliance status and may void insurance coverage for machinery damage events.
• Deterministic Alarm Response: Because the scale factor is preserved, the vibration monitor’s high-alert and danger setpoints remain accurate. A 125 µm (5 mil) danger setpoint corresponds to a precise output voltage; scale factor drift from a non-OEM cable shifts this correspondence and can cause either spurious trips or missed danger conditions.
• Plug-and-Play Replacement: The 330930-040-00-05 is a direct form-fit-function replacement for the original cable. Connector geometry, cable diameter, and armor OD are identical to the factory-installed assembly, allowing installation without modification to cable glands, conduit fittings, or junction box entries.
• ATEX/IECEx Zone Integrity: In hazardous-area installations, the system-level ATEX/IECEx certification is contingent on using certified components. Replacing the extension cable with a non-certified assembly breaks the certification boundary and requires re-assessment by a notified body before the installation can be returned to service in a classified area.
• Reduced Diagnostic Ambiguity: When a vibration anomaly is detected, maintenance engineers must determine whether the signal represents a genuine machinery fault or a measurement artifact. Using OEM cables eliminates cable-induced artifacts from the diagnostic decision tree, reducing mean time to diagnosis (MTTD) for genuine faults.
• Long-Term Signal Stability: The low-loss dielectric and robust armor construction minimize signal attenuation and noise floor degradation over multi-year continuous operation. This is particularly relevant in base-load power generation and continuous-process petrochemical plants where machinery runs for 18–36 months between planned outages.
• Inventory Standardization: The 330930-040-00-05 is the most widely deployed 5 m extension cable in the 3300 XL ecosystem. Stocking this part number covers the majority of 3300 XL installations in a typical plant, simplifying spare parts management and reducing the number of line items in the critical-spares inventory.

Quality Assurance & Global Logistics

Every 330930-040-00-05 unit supplied through siemensplc.com is sourced from verified distribution channels with full part traceability. Pre-shipment inspection covers connector mechanical integrity, armor continuity, and jacket condition. Original manufacturer packaging is retained where available. We do not supply re-labeled, counterfeit, or unverified assemblies. Certificates of conformance and traceability documentation are available upon request for plant incoming inspection requirements.

Logistics operations are based in Xiamen, China — a major international port city with direct air freight connections to Singapore, Dubai, Frankfurt, Los Angeles, and Tokyo. Standard international shipments depart within 1–3 business days of order confirmation. Expedited same-day dispatch is available for critical plant shutdown requirements. DHL Express, FedEx International Priority, and UPS Worldwide Express are the primary carriers. Export documentation, commercial invoices, and packing lists are prepared in compliance with destination country customs requirements. For large-volume orders or project-based procurement, consolidated sea freight via Xiamen Port is available with competitive lead times to major global ports.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026