Bently Nevada 330905-00-16-10-02-05 Proximity Probe – 3300 NSv Series

330905-00-16-10-02-05: 16mm Eddy-Current Proximity Probe in Turbomachinery Protection Loops

In a continuous-duty rotating machinery protection architecture, the proximity probe is the first transducer in the measurement chain — and the one with the least tolerance for error. The Bently Nevada 330905-00-16-10-02-05 is a 16mm eddy-current proximity probe from the 3300 NSv (Non-contacting Vibration) Series, engineered specifically for real-time, non-contact measurement of shaft radial vibration, axial position, and differential expansion in heavy industrial turbomachinery. It operates as the primary sensing element in API 670-compliant machinery protection systems, feeding calibrated displacement signals to 3300 XL monitor modules for continuous trip and alarm evaluation.

The probe’s operating principle is based on Faraday’s law of electromagnetic induction. A high-frequency oscillator — housed in the matched driver/oscillator unit — drives an alternating current through the probe tip coil, generating a focused electromagnetic field. When a conductive target (the rotating shaft) enters this field, eddy currents are induced on the shaft surface, loading the oscillator circuit and producing a voltage output that is linearly proportional to the gap distance between probe tip and shaft surface. The 16mm tip geometry extends the linear measurement range to approximately 0.25 mm to 2.54 mm (10 to 100 mil), making it the correct selection for large-diameter rotors where smaller 8mm or 11mm probes would produce insufficient field penetration depth and a compressed linear range.

The 330905-00-16-10-02-05 is a direct, calibrated component within the Bently Nevada 3300 NSv measurement chain. It must be used with a matched 330130-series extension cable and a 3300 XL 16mm driver/oscillator (part number 330180-X1-05 or equivalent) to maintain the factory-calibrated sensitivity of 7.87 V/mm (200 mV/mil). Substituting unmatched extension cables or drivers will shift the system sensitivity and introduce measurement error that will not be flagged by the monitor — a critical failure mode in protection-grade installations.

Real-time Stock & RFQ: [email protected] | WhatsApp: +86 18359268345

Technical Parameters

Hardware Logical Analysis

The 16mm probe tip geometry of the 330905-00-16-10-02-05 is not an arbitrary dimensional choice — it is a deliberate electromagnetic design decision. A larger coil diameter produces a wider and deeper electromagnetic field cone, which serves two functions: it increases the effective linear range of the gap-to-voltage transfer function, and it reduces sensitivity to minor surface irregularities on the shaft target area (runout, scratches, plating variations). For large-diameter shafts — typically above 100mm journal diameter — the 16mm probe maintains field uniformity across the target zone, whereas an 8mm probe would exhibit field edge effects that introduce non-linearity at the extremes of the measurement range.

The integral armored cable is a coaxial construction with a stainless-steel outer braid and a PTFE-insulated center conductor. This construction serves a dual purpose: mechanical protection against abrasion, oil mist, and vibration fatigue in the cable routing path, and electromagnetic shielding against radiated interference from adjacent motor drives, bus bars, and high-current switching equipment. The shield is grounded at the driver/oscillator end only — a single-point ground topology that prevents ground loop currents from modulating the signal. In installations where the probe is routed near variable-frequency drives (VFDs) or high-power contactors, this shielding architecture is the primary defense against common-mode noise injection into the measurement chain.

The 3300 NSv system uses a three-component calibration approach: probe, extension cable, and driver/oscillator are calibrated as a matched set against a standard AISI 4140 steel target at the factory. The calibration data is embedded in the driver/oscillator, not the probe. This means the probe itself is a passive transducer — its performance is entirely determined by the electromagnetic properties of its coil geometry and the dielectric properties of its tip material. There are no active components, no firmware, and no configuration parameters in the probe. This architecture maximizes reliability in high-temperature environments where active electronics would degrade, and it simplifies field replacement: a probe swap requires no recalibration of the monitor, only verification that the replacement probe matches the original tip diameter and cable length.

EMC performance is further enhanced by the probe body material — a non-magnetic stainless-steel housing that does not distort the probe’s electromagnetic field and does not become magnetized in the presence of strong external fields from adjacent machinery. In installations near large synchronous motors or generators, probe body magnetization is a documented failure mode in lower-grade sensors; the 3300 NSv housing material specification eliminates this risk.

System Integration Benefits

• Direct API 670 Compliance: The 330905-00-16-10-02-05 meets the full requirements of API Standard 670 (5th Edition) for non-contacting vibration measurement systems, enabling use in protection-grade installations without additional qualification testing or derating.
• Deterministic Signal Latency: The analog voltage output of the eddy-current measurement chain introduces no digital processing latency. The monitor receives a continuous, real-time signal with no sampling delay — critical for trip response times in the 1–5 ms range required by API 670 protection logic.
• Zero Mechanical Wear: Non-contacting measurement eliminates all tribological degradation mechanisms. Probe sensitivity does not drift due to mechanical wear, and there is no contact force that could influence shaft dynamics or introduce measurement artifacts at low vibration amplitudes.
• Wide Thermal Operating Envelope: The -35°C to +177°C probe tip rating covers the full range of industrial turbomachinery bearing housing temperatures, including high-temperature steam turbine applications where bearing metal temperatures can approach 150°C under load.
• Plug-Compatible Replacement: The 330905-00-16-10-02-05 is dimensionally and electrically identical to previous-generation 3300 NSv 16mm probes. Field replacement requires no modification to probe mounting hardware, cable routing, or monitor configuration — reducing planned maintenance downtime to the time required for physical probe swap and gap verification.
• Diagnostic Transparency via Gap Voltage: The DC gap voltage output provides a continuous, observable diagnostic channel. Operators can monitor gap voltage trends to detect probe tip contamination, shaft centerline migration, bearing wear progression, and thermal growth — all without interrupting the protection function.
• Multi-Parameter Measurement Capability: A single 330905-00-16-10-02-05 installation can simultaneously provide radial vibration (AC component), shaft average centerline position (DC component), and — in axial installations — thrust position data. This multi-parameter output from a single transducer reduces the total number of penetrations required in the bearing housing.
• Compatibility with Redundant Monitoring Architectures: The probe’s analog output can be split to feed multiple monitor inputs simultaneously, supporting 1oo2 (one-out-of-two) or 2oo3 (two-out-of-three) voting logic architectures without signal conditioning or active splitting hardware — a passive split using high-impedance monitor inputs is sufficient.

Quality Assurance & Global Logistics

Every 330905-00-16-10-02-05 unit supplied by siemensplc.com is sourced through verified industrial distribution channels with full part number and label authentication against Bently Nevada OEM documentation. Pre-shipment inspection includes visual examination of probe tip condition, connector integrity, cable armor continuity, and coaxial cable insulation resistance. Units exhibiting any evidence of tip damage, connector corrosion, or cable jacket compromise are rejected prior to dispatch.

Packaging follows ESD-safe and moisture-barrier protocols: each probe is individually wrapped in anti-static foam, sealed in a moisture-barrier poly bag with desiccant, and packed in a rigid outer carton with void fill to prevent cable coil stress during transit. For international shipments, export documentation includes commercial invoice, packing list, and certificate of origin. Certificates of conformance and traceability documentation are available upon request at the time of order placement.

Logistics operations are based in Xiamen, China, with direct access to Xiamen Gaoqi International Airport (XMN) and Xiamen Port for both air freight and sea freight consolidation. Standard export shipments are dispatched via DHL Express, FedEx International Priority, or UPS Worldwide Express, with typical transit times of 3–5 business days to major industrial hubs in Southeast Asia, the Middle East, Europe, and the Americas. For urgent requirements, same-day dispatch is available for orders confirmed before 14:00 CST. All shipments include full tracking and are covered by cargo insurance.

Contact Information

Email: [email protected]
WhatsApp: +86 18359268345
Web: siemensplc.com
Location: Xiamen, China
© 2026 siemensplc.com. All rights reserved.