ABB 3HAC047118-003 Teach Pendant

ABB 3HAC047118-003 FlexPendant: Stop the Clock on Your Downtime — Ships Today from Xiamen

Your IRB 6700 line is down. The FlexPendant is dead — cracked screen, unresponsive touchscreen, or a communication fault that won’t clear. Every minute the robot sits idle, you’re burning through production targets and explaining delays to management. You don’t need a sales pitch. You need a 3HAC047118-003 on a plane tonight.

We stock the ABB 3HAC047118-003 FlexPendant in Xiamen, China — verified, tested, and ready to ship via DHL Express or FedEx Priority. Most orders placed before 18:00 CST clear customs documentation the same day. This is the exact OEM teach pendant for the IRC5 controller platform (DSQC3060 / 3HAC064211-001), covering all IRB 6700 payload/reach variants.

URGENT REQUIREMENT? Contact: [email protected] | WhatsApp: +86 18359268345

Quick Technical Datasheet

Troubleshooting & Replacement Tips

Most FlexPendant failures on the IRB 6700 fall into three buckets. Here’s what to check before you pull the trigger on a replacement — and what to do the moment the new unit arrives.

Fault 1 — Blank or Frozen Screen (No Boot)
Nine times out of ten this is a failed touchscreen controller board, not the IRC5 itself. Confirm by checking the IRC5 teach pendant port voltage (should read 24 VDC on pins). If voltage is present and the pendant still won’t boot, the pendant is the fault. No amount of power cycling will fix a dead display driver IC.

Fault 2 — Communication Lost / Event 20223
Event log code 20223 (FlexPendant connection lost) can be the cable, the RJ45 connector at the controller end, or the pendant’s internal Ethernet controller. Swap the cable first — it’s a 10-minute job. If the fault follows the pendant to a known-good cable, the pendant’s NIC is gone. Replace the unit.

Fault 3 — Enabling Device (Deadman) Fault
If the robot refuses to enter manual mode and the event log shows a safety chain fault tied to the enabling device, the 3-position switch inside the pendant has failed. This is a safety-critical component — do not attempt to bypass or tape it. Replace the pendant immediately. IRC5 will not allow T1/T2 mode without a verified enabling device signal.

Replacement Procedure — Key Steps:

• Power down the IRC5 controller to OFF (not just E-stop). The FlexPendant is hot-swap capable in theory, but on a production line, don’t risk it.
• Disconnect the umbilical at the controller cabinet port. Note the cable routing — the 10 m cable has a specific strain-relief bracket on most IRB 6700 installations.
• Connect the new 3HAC047118-003. Power up the IRC5. The pendant auto-negotiates with the DSQC3060 main computer — no IP configuration required. It pulls its identity from the controller.
• On first boot with a new pendant, RobotWare will prompt a language selection and may request a FlexPendant calibration (touchscreen alignment). Complete this before handing back to operators.
• Verify the enabling device by entering T1 mode and confirming the robot accepts jog commands only while the deadman is held in the middle position. Test all three positions: released (motors off), middle (motors on), fully pressed (motors off). If any position fails, the pendant is defective — contact us immediately.
• Check the event log (Event Log > Common) for any residual faults from the previous pendant. Clear them and confirm no new faults appear within 5 minutes of operation.
• If your system runs RobotWare options (Arc, PickMaster, Force Control), verify the option licenses are still active under System Info. Pendant replacement does not affect licenses — they are stored in the DSQC3060, not the pendant.

Firmware Note: The 3HAC047118-003 runs firmware embedded in RobotWare. When you connect a new pendant to an IRC5 running RobotWare 6.x, the controller automatically pushes the correct pendant firmware version. No manual flashing required. If your IRC5 is on RobotWare 5.x, contact us before ordering — there are compatibility constraints.

Reliability in Harsh Conditions

The IRB 6700 is ABB’s workhorse for heavy-payload applications — foundries, press shops, body-in-white lines. The FlexPendant lives in that same environment. The 3HAC047118-003 is built to handle it.

The IP54-rated housing blocks coolant mist, metal dust, and the kind of airborne particulate that kills consumer electronics in minutes. The polycarbonate housing is impact-resistant — designed to survive being dropped on a concrete floor during a shift change, not just sit on a desk in a lab. The 7-inch touchscreen uses a resistive panel, not capacitive, which means it responds to gloved hands and doesn’t false-trigger from water droplets or metal chips landing on the surface.

Internally, the PCB assembly is conformal-coated to resist humidity and condensation — critical in facilities that run washdown cycles or operate in coastal climates. The umbilical cable uses a reinforced PUR jacket rated for continuous flexing, which matters on installations where the pendant is picked up and set down hundreds of times per shift. The RJ45 connector at the pendant end is shielded and strain-relieved; the most common cable failure point is the controller-end connector, not the pendant itself.

Vibration resistance is validated to IEC 60068-2-6 levels — the pendant will not develop intermittent faults from the structural vibration of a press shop floor or the resonance of a large robot at full speed. Thermal operating range covers -10°C to +52°C, which handles most industrial environments including unheated warehouses in northern climates and non-air-conditioned production halls in summer.

Global Express Logistics

We operate from Xiamen, China — one of the country’s primary export hubs with direct DHL and FedEx gateway access. Here’s exactly how your order moves:

• Order Confirmation: You place the order and send payment confirmation. We issue a proforma invoice and begin export documentation (commercial invoice, packing list, HS code 8537.10 declaration) within 2 hours during business hours.
• Same-Day Dispatch: Orders confirmed before 18:00 CST are packed, ESD-bagged, and handed to DHL/FedEx the same evening. The unit ships in a double-wall carton with foam inserts.
• Transit Times: DHL Express to Europe: 3–5 business days. FedEx Priority to North America: 3–4 business days. Southeast Asia: 2–3 business days. Middle East: 4–6 business days. These are real-world averages, not marketing estimates.
• Tracking: You receive a waybill number within 12 hours of dispatch. We monitor the shipment and proactively flag any customs holds.
• Export Compliance: The 3HAC047118-003 is not subject to EAR export controls for most destinations. If your country requires an End-User Certificate or import permit, notify us at order time and we’ll prepare the documentation.
• Customs Value: We declare accurate commercial value — we do not undervalue shipments. This protects you from customs seizure and ensures your company’s import records are clean.

Contact Information

Line down? Don’t wait for a contact form response.

📧 Email: [email protected]
📱 WhatsApp: +86 18359268345 — fastest response channel for urgent requirements
🌐 Web: siemensplc.com

© 2026 siemensplc.com. All rights reserved. Xiamen, China.