Siemens 6EP1334-1LB00 Industrial Power Supply

Siemens 6EP1334-1LB00 — Stop the Clock on Your Downtime. Ship Today.

Every minute your line is down, you’re bleeding money. The Siemens 6EP1334-1LB00 SITOP PSU100L 24 VDC / 10 A power supply is one of the most common single points of failure in SIMATIC S7 control panels — and when it goes, it takes everything with it. We stock it. We ship it today. From Xiamen to your dock, DHL Express, no excuses.

This is not a generic listing. This is a field-sourced, 100% original Siemens unit, pulled from verified supply chains, inspected before it leaves our warehouse. If your maintenance team is standing in front of a dead panel right now, this is the page they need.

URGENT REQUIREMENT? Contact: [email protected] | WhatsApp: +86 18359268345

Quick Technical Datasheet

Troubleshooting & Replacement Tips

After handling hundreds of PSU100L failures in the field, here’s what actually matters when you’re doing a hot swap under pressure:

Common Failure Signatures

• DC OK LED off, no output voltage: Classic internal capacitor failure or blown primary fuse. Don’t waste time probing — swap the unit.
• Output voltage present but unstable (flickering HMI, random CPU resets): Output capacitor degradation. The PSU is dying slowly. Replace before it takes the CPU with it.
• Overload LED latched on: Check downstream load first — a shorted 24 VDC field device will keep tripping the PSU. Disconnect loads in segments to isolate the fault before condemning the supply.
• Intermittent DC OK signal triggering S7 CPU STOP: The DC OK relay contact (terminals 11/12) may be chattering. Verify wiring integrity and contact resistance before replacing the PSU.
• Unit warm to touch but no output: Thermal shutdown triggered by blocked ventilation or ambient above 60 °C. Clear airflow, let it cool 10 minutes, then retest before ordering a replacement.

Replacement Procedure — Step by Step

• Step 1 — Isolate: De-energize the panel. Lock out / tag out per your site procedure. Confirm 0 VAC at input terminals with a calibrated meter — do not trust the breaker alone.
• Step 2 — Document: Photograph terminal wiring before disconnecting anything. The PSU100L uses screw terminals; label each wire if your panel drawing is not current.
• Step 3 — Remove: Loosen input terminals (L, N, PE) and output terminals (+ and −). Slide the DIN rail latch down and tilt the unit off the rail. No tools required beyond a flat-blade screwdriver.
• Step 4 — Inspect: Check the DIN rail clip on the new unit before mounting. Verify the output voltage trim pot is at center position (factory default = 24.0 V). Do not adjust unless your system requires a non-standard setpoint.
• Step 5 — Mount & Wire: Clip onto rail, reconnect PE first, then L and N, then DC output + and −. Torque to 0.5–0.6 Nm on input terminals, 0.5 Nm on output terminals. Do not overtighten — the terminal blocks are plastic-bodied.
• Step 6 — Commission: Energize with loads disconnected. Verify 24.0 VDC ±0.5 V at output terminals. Confirm DC OK LED is solid green. Reconnect loads progressively. Monitor for 5 minutes before returning to automatic operation.
• No DIP switches, no firmware, no addressing required. The PSU100L is a passive supply — plug and play once wired correctly.

Configuration Notes

• Output voltage is adjustable via front-panel trim pot — factory set to 24.0 V. Only adjust if your system explicitly requires a different setpoint (e.g., long cable runs requiring voltage compensation).
• The DC OK relay output (terminals 11/12, normally open) can be wired to a CPU digital input for predictive fault detection. If your existing installation uses this feature, verify the new unit’s relay wiring matches.
• For parallel redundant configurations using a SITOP redundancy module (6EP1961-2BA11), ensure both PSUs are trimmed to identical output voltages before enabling the redundancy module.

Reliability in Harsh Conditions

The PSU100L was not designed for a clean server room. It was designed for the kind of environment where your panel is next to a press, a furnace, or a coastal compressor station. Here’s what it handles without complaint:

• Vibration: Tested to IEC 60068-2-6 (sinusoidal) and IEC 60068-2-27 (shock). The DIN rail mounting provides mechanical damping; the internal components are conformal-coated on production variants. In high-vibration applications (presses, compressors), verify the DIN rail end-stops are tight — a loose PSU will fail prematurely regardless of brand.
• Temperature: Rated 0 °C to +60 °C continuous. Derating applies above 45 °C — output current must be reduced by approximately 2.5% per degree above 45 °C. At 60 °C, maximum continuous output is approximately 6.25 A. If your panel regularly exceeds 50 °C ambient, size up to the 20 A variant or add forced ventilation.
• Humidity: Rated to 95% RH non-condensing. In coastal or high-humidity environments, ensure the panel door seal is intact. Condensation on PCB traces is the primary cause of premature PSU failure in tropical installations — not the unit itself.
• EMC: Compliant with EN 61000-6-2 (industrial immunity) and EN 61000-6-4 (industrial emissions). The wide-range input includes active PFC, which reduces harmonic disturbance on shared supply circuits — relevant in facilities with large VFD loads on the same distribution panel.
• ATEX Zone 2: Certified for use in areas with occasional explosive atmosphere risk. Verify your installation zone classification before specifying — Zone 1 requires a different product family.

Global Express Logistics

Our warehouse is in Xiamen, Fujian — one of China’s primary industrial export hubs with direct access to DHL, FedEx, and UPS international gateways. Here’s how your order moves:

• Order confirmed before 15:00 CST: Same-day dispatch. Tracking number issued within 2 hours of pickup.
• DHL Express Worldwide: Xiamen → most European destinations in 2–3 business days. Southeast Asia in 1–2 days. North America in 3–4 days.
• FedEx International Priority: Available on request for destinations where FedEx has stronger coverage (Middle East, South Asia, Latin America).
• Documentation: Commercial invoice, packing list, and certificate of origin issued with every shipment. HS code 8504.40 (static converters). ECCN EAR99 — no export license required for most destinations.
• Customs clearance: We declare accurate values and descriptions. No under-declaration. If your import team needs specific documentation (EUR.1, Form A, or country-specific certificates), advise at time of order.
• Emergency freight: For critical plant-down situations, contact us directly via WhatsApp for same-day courier booking and priority handling. We have handled emergency shipments to offshore platforms, remote mining sites, and island facilities — if there’s a flight, we’ll get it on it.

Contact Information

Your line cannot wait. Reach us now:

• Email: [email protected]
• WhatsApp: +86 18359268345
• Web: siemensplc.com

© 2026 siemensplc.com. All rights reserved.